...
Search
Close this search box.

Rounder Top Pickets for Houseblocks With Kids and Dogs

A rounder top picket is what a buyer asks for when a houseblock fence has to stop being sharp without turning into a wall. The pages here do not sell a picket under that name, and that gap is worth closing before an enquiry goes out.

What is published is specific: the steel picket page states there are three top designs — spear top, flat top, and a 45 degree bend carrying a spear — picket sections run from 19 x 19 mm upward, rails are welded in twos, threes and fours, and the height ladder appears in inches on one page and millimetres on another.

Key Takeaways

  • No page here uses the word rounder. The steel picket page names three heads: spear top, flat top, and bending 45 degree with spear top.
  • Flat top is a catalogued option, not a compromise: the steel pickets table carries a row reading Top point — Flat top, alongside panel sizes 2400 x 2100, 2100 x 1800 and 1800 x 1500 mm.
  • Heads are punched, then polished, then coated. The process line runs pre-galvanised pipe, cut, punched, welded, polished, powder coated — with powder coating published at 60 and 120 microns.
  • Picket sections are published — 19 x 19, 20 x 20, 25 x 25 mm — but centres are not, and neither is the gap under a rail. Those two decide a dog and belong in the enquiry.
  • The feature list on the steel picket page includes keeping a dog and a child safe, and the same page states ASTM A-653 G90 coating on pickets and posts.

Which Heads Are Actually Published

The steel picket page states the design set plainly: three tops, one spear, one flat, and one bent at 45 degrees carrying a spear. Under the manufacturing paragraph, the pickets are described as pre-galvanised square tubular with inner pickets punched to a spear, or just flattened at the top, then welded to two, three or four horizontal rails and powder coated.

So a rounder top is one of two requests, and the enquiry should say which: flat top — a level cut with no point, which the steel pickets table catalogues in its own row — or the published spear deburred at a stage you name in the enquiry. The garrison page describes a crushed spear top welded into heavier rails, which is where the standard head sits before any softening is asked for.

Two arguments live on other pages and are not re-opened here: the security, safety and cost case for spear against flat, made in the site’s comparison of spear top versus flat top tubular steel fences, and the institutional child-environment question, made in the guide to bow top versus spear top fencing for schools and playgrounds. What follows is the residential line only.

Black metal fence whose flat-topped vertical pickets rise above the upper horizontal rail, with a modern industrial building and a strip of young planted trees behind

What a Kid and a Dog Actually Meet

The steel picket page lists keeping a dog, a child and a pool area safe among the reasons buyers specify this fence; pool fencing itself is a separate product family and is not argued here. The residential decision sits in three numbers, and only one is published.

Sections are published. The steel pickets table gives pickets at 19 x 19, 20 x 20 and 25 x 25 mm, rails at 40 x 40, 30 x 30 and 40 x 30 mm, and posts from 50 x 50 to 80 x 80 mm; the garrison table states 25 mm pickets on 40 mm rails. Heights are published twice over — 36, 48, 54, 60 and 72 inches with two, three or four rails on one list, 1.8 to 2.4 m on another, and panels at 1500, 1800, 2100 and 2400 mm in the tables.

Centres are not published. No picket page states the spacing between verticals, and none states the clearance under the bottom rail. On a houseblock those two dimensions decide whether a puppy goes under or a head comes through, so they cannot be left to a drawing stage.

The same is true of the head itself once it is cut. A trimmed spear is a finishing step rather than a fourth design, and the only published evidence that a finishing step exists is the process chain on the steel pickets page, which places polish before powder coating. Ask for the head described in words, and ask which stage removes the burr.

Close-up of a galvanised square steel post with a bolted metal clamp holding a horizontal rail, and a row of pickets with obliquely cut, pointed tops, workshop wall and a truck in the distance

Coating, Caps and Where Bare Steel Is

Two coating routes are published, and they are not the same promise. The default is pre-galvanised pipe cut, punched, welded, polished and powder coated, with powder coating given in the steel pickets table at 60 and 120 microns and PVC at 450 and 650 microns. The alternative is black tube welded then hot-dip galvanised, which the steel picket page says will not fade for at least three years. Above 42 microns is published for that outdoor hot-dip line; no finished-panel zinc figure is published for pickets.

Those three answer different questions and are easy to mix up in an enquiry. The steel picket page quotes ASTM A-653 with a G90 coating at 0.90 oz/ft² on pickets and posts, plus yield strength of 45,000 psi (310 MPa) for pickets and 50,000 psi (344 MPa) for rails. G90 is a coating class on the strip the tube is made from, and the psi figures are strength, not zinc — neither replaces a stated hot-dip thickness on the finished panel.

Bare steel appears where the drawing stops: a cut picket end, a drilled field hole, the top of a post. The steel pickets packing note states each post ships with its cap covered well, and the site lists a galvanised round post cap in 80 NB — which post section it suits is a written question, not a guess. The garrison page claims 20 or more years of service where hot-dip galvanising and powder coating are both applied; treat that as the page’s own claim and ask what supports it at your address.

Specifying a Houseblock Run

Write the run as one page: each line below has a published value, or is a gap only a written answer closes.

Line to write Published choice Ask in writing
HeadSpear top, flat top, 45 degree bend with spearWhich stage deburrs a trimmed spear
GeometryPickets 19 x 19 / 20 x 20 / 25 x 25 mm; rails 2, 3 or 4Picket centres and bottom clearance
Height1500 / 1800 / 2100 / 2400 mm, or 36 to 72 inchesWhich unit your drawing uses
CoatingPre-galvanised plus powder coat at 60 or 120 microns; or hot-dip after weldingFinished-panel zinc thickness, not strip class
OpeningsSliding, electric sliding and swinging gates are listedLatch height and gap for your dog

Colour and posts follow the same rule. The product page states pre-galvanised and powder coated in black or other colours, with no colour schedule, and the steel picket page gives 60 x 60 x 2 mm posts cut 3 m rather than the 2.6 m it says others supply. Name the section, the length and the finish, and ask what the minimum order is when a houseblock needs twenty panels and two gates rather than a container.

Specify the fence from the ground up, not the tips down: centres and clearance decide whether the dog stays inside, and the head only decides what a hand meets.

Frequently Asked Questions

Is a rounder top picket a product you sell?

Not under that name. Three heads are published — spear top, flat top and a 45 degree bend carrying a spear — so a rounder top means flat top, or a trimmed spear deburred at a stage you name. Say which in the enquiry.

What picket spacing keeps a dog in a yard?

No picket page here publishes centres or the gap under the bottom rail. Sections are published from 19 x 19 to 25 x 25 mm. State the gap you need and ask whether the panel can be welded to it.

Which coating route should I ask for on a picket panel?

Ask for the finished-panel figure, not a strip class: pre-galvanised pipe with 60 or 120 micron powder coating, or black tube welded then hot-dip galvanised after welding. The sheared end and any drilled hole are where bare steel shows.

Can post caps be supplied with a picket order?

Posts ship with their cap covered, and a galvanised round post cap in 80 NB is listed separately. Which cap fits a 50 x 50 or 60 x 60 picket post should be confirmed in writing.

Conclusion

A rounder top picket is a readable request once translated into what this site publishes: a head from the three named designs, a section from the tables, a height in one unit, and a coating route stated as a finished panel rather than a strip class.

The two numbers that decide a family yard are the ones with no published value — centres and clearance — so put them in the enquiry first and let the head be the last line discussed.

Facebook
Twitter
LinkedIn
Pinterest
engineer cooperation two asian male female technician maintenance inspect relay robot system with tablet laptop control quality operate process work heavy industry 40 manufacturing factory

Talk To Our Expert

Connect with our specialists to discuss your needs and confidently start your project!

Picture of Frank Zhang

Frank Zhang

Hey, I'm Frank Zhang, the founder of DB Fencing, Family-run business, An expert of metal fence specialist.
In the past 15 years, we have helped 55 countries and 120+ Clients like construction, building, farm to protect their sites.
The purpose of this article is to share with the knowledge related to metal fence keep your home and family safe.

Categories

Recent Posts

Table Of Contents

We are at your disposal for any technical or commercial information

Table Of Contents

Picture of Frank Zhang

Frank Zhang

Hi, I’m Frank Zhang, the founder of DB Fencing, I’ve been running a factory in China that makes metal fences for 12 years now, and the purpose of this article is to share with you the knowledge related to metal fences from a Chinese supplier’s perspective.
Facebook
Twitter
LinkedIn

Ask For A Quick Quote

We will contact you within 1 working day, please pay attention to the email “info@metalfencetech.com”.

Your Email is necessary!!!