...
Search
Close this search box.

Loop Legs vs Square Legs on Wet Australian Clay: Which Stops Sinking and Which Stops Creep

Loop legs are specified on this site’s corral panel pages against one failure and one only: the page states that loop legs prevent each panel from sinking into moist or soft soils. Ask about a clay yard and that sentence is the whole answer the pages give to sinking, while the second failure wet clay causes — a line of panels creeping out of square along its length — is answered by a sentence that appears on three pages under three different shape-words.

Sinking is a bearing question, creep a lateral one, and the site’s wording assigns them to different lines. For a buyer specifying loop legs versus square legs on saturating clay, that split is the order, not a footnote: it decides which page you quote from and which sentence you ask to see repeated on the proforma.

Key Takeaways

  • The sinking claim is published in one sentence, on the round-leg page and repeated word for word on the triangle-leg page: loop legs prevent each panel from sinking into moist or soft soils.
  • The movement sentence travels: the same wording appears on the straight-leg page with Square as its subject, on the triangle-leg page with Triangle, and on the category page with J-shaped legs.
  • There is no square-leg page in the current site index. The navigation label points to the corral panel category page, which groups straight, triangle, square and J-shaped legs as preventing sinking by avoiding ground penetration.
  • Leg choice is entangled with panel build: the round-leg page runs 16, 19 and 20 gauge tubing with two vertical Z braces, the triangle page 18 gauge with one or two round pipe braces, the straight-leg page 16 gauge with one vertical stay.
  • Nothing on these pages publishes a bearing area, a sink depth, a clay figure or a load rating for any leg, so those four go to the factory as written questions.

Two Failures, Two Sentences

Walk the yard after two days of rain and note which of two things happened. Either a panel sits lower than its neighbours, the leg having entered the ground, or the line has opened up — panels level, but no longer straight and the pins in strain. The first is sinking, the second is creep, and a wet clay yard can give you both in a week.

The published claims map onto those two observations unevenly. The round-leg page states that loop legs prevent each panel from sinking into moist or soft soils — the only sinking sentence tied to one shape. The movement sentence travels: the straight-leg page carries it with Square as its subject, the triangle-leg page with Triangle, and the category page with J-shaped legs. Sinking belongs to the loop. The small contact point belongs to whichever shape the page you are reading happens to name.

Rows of galvanised stock panels stacked indoors, the loop legs forming a U-shape at each end of the frame, on a concrete factory floor

Where the Square Leg Actually Lives

Here is the difficulty with a loop-versus-square decision. The site publishes pages for round, triangle and straight legs, and — in the current page index — no page for square legs; the navigation entry labelled square legs links to the corral panel category page instead. That category page does name the shape, and groups it: straight, triangle, square and J-shaped legs are stated to prevent sinking and to keep panels portable by avoiding ground penetration. It also lists seven bottom leg types, including no-leg panels.

So a square leg carries a sinking claim by grouping on the category page, and a movement claim on a page titled for straight legs. Two wrinkles follow. The loop-leg sinking sentence is repeated word for word on the triangle-leg page, which sells triangle legs — ask whether that is a template carried across pages or a claim about the shape named in it. And the straight-leg page gives its own leg no function sentence at all, while naming Square in the one it does carry.

Claim you need Where it is published Wording on the page Ask in writing
Panel must not sinkRound-leg pageLoop legs prevent sinking in moist or soft soilsDoes this apply to the SKU quoted?
Line must not creepStraight page (says Square), triangle page (Triangle), category page (J-shaped)Small ground contact point prevents panel movementWhich shape does your page name?
Square leg behaviourStraight-leg page, plus the category page groupingSquare, triangle, straight and J-shaped stated to prevent sinkingHave the shape-word repeated on the proforma
Panels tied in a lineAU panel page and leg pagesPin hookups; sets of U lugs, L lugs and pinsWhich connectors ship with the legs?

The Build Changes With the Leg

A leg page is also a panel specification, and the three pages differ in ways that matter more than the foot. The round-leg page lists six bars in 2 in. or 1-3/4 in. round tubing with continuous welded saddle joints, two vertical Z braces, 16, 19 and 20 gauge, at heights of 5 ft., 62 in. and 72 in., with a quick pin latch and u-supports. The triangle page lists six bars of 1-5/8 in. round rails in 18 gauge with one or two vertical round pipe braces, at 6 ft. The straight page lists 2 in. diameter 16 gauge tubing with one vertical stay, in 3, 4 and 6 bar versions, hot dipped galvanised and powder coated in grey.

Galvanised stock panels with straight legs standing on patchy grass and bare ground, horizontal rails welded to rectangular frames

Choosing a foot therefore changes wall thickness, rail diameter and brace count at the same time. On a clay yard that is the whole argument: the panel that resists sinking is also the panel whose rails and braces you have just changed, and a heavier gauge may survive stock pressure better than any leg shape. Compare that with the millimetre rows on the Australian cattle panel page — the 1800 x 2100 mm row lists six 60 x 30 mm oval rails in a 40 x 40 mm RHS frame, shipped with rain caps, U lugs, L lugs, pins and two foot plates; the 1600 x 2100 mm row lists five 80 x 40 mm oval rails in a 50 x 50 mm RHS frame. Same job, different unit system, and a third ground interface that is a plate rather than a leg.

Close view of stacked galvanised panels with horizontal rails welded to a rectangular frame, their flat base plates with punched holes resting on dirt and gravel

Specifying a Clay Yard in Writing

Write the failure, then the shape, then the unit. State that the yard is clay and holds water, that panels have sunk or the line has crept, and that you need the leg whose published claim covers that behaviour. Ask for the gauge, rail diameter and brace count of the exact leg line quoted, in the units you ordered in — the leg pages use feet and inches, the Australian panel page millimetres, and a purchase order that mixes the two invites a substitution.

Then ask the four things no page answers: how deep a leg is expected to sit in saturated ground, what the contact area of each shape actually is, whether the legs are welded or attached, and how the panel is tied to its neighbour once pinned. The comparison of leg types by terrain covers the general selection, and the anatomy of the oval rail and square post frame covers the rails themselves, so this article stops at what the pages do not state. Our position: on saturating clay, order against the sinking claim, which the published wording ties to loop legs, and get the movement behaviour of whatever second line you buy confirmed in writing.

Frequently Asked Questions

Do loop legs stop a panel sinking in wet clay?

The round-leg page states that loop legs prevent each panel from sinking into moist or soft soils. No page publishes a sink depth, contact area or soil figure, so ask which leg and which ground the claim covers for your order.

Are square legs and straight legs the same thing?

The category page lists them separately among seven bottom leg types, and the site publishes a straight-leg page but no square-leg page of its own — the square label links to the category page. Treat them as different shapes until a supplier confirms the geometry in writing.

What stops a panel line creeping out of square?

The published wording ties movement to a small ground contact point — for Square on the straight-leg page, for Triangle on the triangle page — and panels are tied to each other with pin hookups and lug-and-pin sets. Ask which shape your quote names.

Why do the panel specs change when I change the leg?

Because each leg page publishes its own build: 16, 19 or 20 gauge with two Z braces on the round-leg page, 18 gauge with one or two pipe braces on the triangle page, 16 gauge with a single stay on the straight page. Read the foot and the frame together.

Conclusion

Wet clay asks two questions of a panel line, and the pages answer one clearly. Loop legs carry the sinking sentence; the movement sentence is the same wording with a different shape-word on each page, and the square leg has no page of its own. So put both the shape and the sentence naming it on your purchase order.

Name the failure you are seeing, quote the leg whose published claim covers it, and have the four unpublished figures — contact area, expected sink, leg attachment and how panels tie together — answered in writing before the order moves. The photographs here show loop legs on a warehouse floor and straight legs on patchy grass and bare dirt; ask what the same legs are expected to do on wet clay.

Facebook
Twitter
LinkedIn
Pinterest
engineer cooperation two asian male female technician maintenance inspect relay robot system with tablet laptop control quality operate process work heavy industry 40 manufacturing factory

Talk To Our Expert

Connect with our specialists to discuss your needs and confidently start your project!

Picture of Frank Zhang

Frank Zhang

Hey, I'm Frank Zhang, the founder of DB Fencing, Family-run business, An expert of metal fence specialist.
In the past 15 years, we have helped 55 countries and 120+ Clients like construction, building, farm to protect their sites.
The purpose of this article is to share with the knowledge related to metal fence keep your home and family safe.

Categories

Recent Posts

Table Of Contents

We are at your disposal for any technical or commercial information

Table Of Contents

Picture of Frank Zhang

Frank Zhang

Hi, I’m Frank Zhang, the founder of DB Fencing, I’ve been running a factory in China that makes metal fences for 12 years now, and the purpose of this article is to share with you the knowledge related to metal fences from a Chinese supplier’s perspective.
Facebook
Twitter
LinkedIn

Ask For A Quick Quote

We will contact you within 1 working day, please pay attention to the email “info@metalfencetech.com”.

Your Email is necessary!!!