...
Search
Close this search box.

Why Six Oval Rails and a Square Post Frame Decide How a Cattle Panel Carries Stock

Six oval rails and a square post frame is what a cattle panel quotation is actually buying. Height and length get the attention on a purchase order. Section shape and the welded connections get nothing, and that is where a portable yard gives way.

The site’s cattle panel page publishes three styles rather than one product: oval pipe, all-square and round tube. All three carry the same rail count at the same height and the same 1.6 mm wall. What separates them is the shape of the tube, and that is the whole conversation.

Key Takeaways

  • The page pairs 6 bars/rails with a 1.8 m height and 5 bars/rails with 1.6 m, at listed lengths of 2.07 m, 2.09 m and 2.1 m, with an “etc.” after the run.
  • Three rail families are published: oval 30 x 60, 40 x 80 and 40 x 120 mm; square 40 x 40 and 50 x 50 mm; round 32 mm and 42 mm outside diameter.
  • Every option in those blocks is written at 1.6 mm wall, so the styles differ in section shape rather than steel gauge.
  • Read as hollow sections at that wall, a 50 x 50 mm vertical is about twice the resistance to bending (stiffness) of a 40 x 40 mm one and about three times a 42 mm round tube. Strength is a separate calculation.
  • Rails are fully welded into the verticals, and caps, lugs, feet and 2 pins are welded onto the post. On a panel built as two end verticals, six rails is twelve welds.
  • Section figures here are a buyer’s arithmetic on the page’s own numbers, not section data from the factory.
  • A second panel page describes two sets of double lugs and two single lugs per panel taking 16 mm pins, which turns the cattle page’s “2 pins” into a question.

What the Three Style Blocks List

Read the cattle fence panel page line by line and three blocks appear in almost identical wording.

Style block Vertical pipe Horizontal rails Rail count
Oval pipe50 x 50 or 40 x 40 mm RHS30 x 60, 40 x 80, 40 x 120 mm oval6 at 1.8 m, 5 at 1.6 m
All square50 x 50 or 40 x 40 mm RHS50 x 50 or 40 x 40 mm RHS6 at 1.8 m, 5 at 1.6 m
Round tube32 mm or 42 mm O.D.32 mm or 42 mm O.D.6 at 1.8 m, 5 at 1.6 m

Every rail and vertical in those blocks is written at 1.6 mm thickness, and all three list the same height and length options: 1.6 m and 1.8 m against 2.07 m, 2.09 m and 2.1 m, each run closed by an “etc.” So a quote reading “cattle panel, 1.8 m, six rail” answers the questions that differentiate nothing and skips the one that does.

The build sequence is published too: pre hot-dip galvanised pipe, horizontal rails fully welded with the vertical post, then steel caps, lugs, feet and 2 pins welded onto the post, with epoxy paint on the weld joints. The oval and square style blocks both carry a zinc coating line reading “More than 15 microns”, and the site records 18-28 microns for this livestock line per the product page. Ask which figure covers rails, verticals and weld paint, because those are three coating operations.

The Load Path: Rail, Post, Lug, Pin

Stock pressure arrives on a rail. From there it has three places to go: along the rail into the vertical it is welded to, down that vertical into the foot, and across the joint into the next panel through lugs and pins.

Six rails welded into two verticals is twelve rail-to-post joints per panel. That is a buyer’s count from the page’s construction sentence, and it assumes a panel built as two end verticals, which is worth checking against the drawing you are quoted. On that reading a 20-panel line carries 240 joints plus 19 panel-to-panel connections.

A close view of a galvanised livestock panel joint on grass: oval horizontal rails welded into a square vertical post, a welded lug plate with a pin through it, and a flat plate foot with a bolt hole at the base

The joint is where the two panel pages stop agreeing. The cattle page lists 2 pins per panel among the welded items. The sheep yard panel page, which uses the same oval, square and round families at 1.6 mm and 2.0 mm walls, states that each panel carries two sets of double lugs and two single lugs welded on to accept pins, that 16 mm pins are included, and that rail bars are fully welded with each weld protected by epoxy paint. Two double sets plus two single lugs is six lug openings per panel. Ask how many pins ship to fill them, and whether the diameter is 16 mm.

Feet are the least specified element. The cattle page welds them onto the post without publishing a size, a leg shape or a ground condition. What legs do on soft or wet ground is treated in this site’s corral panel leg types compared.

What Six Rails Do to the Gap

Rail count is a spacing statement, published as a pairing: 6 bars at 1.8 m, 5 bars at 1.6 m. Divide each height by its rail number and the pitch is 300 mm and 320 mm. Divide by the number of gaps instead, which is what you get if the outer rails sit at the top and bottom edges, and the same two panels read 360 mm and 400 mm.

That 60 mm spread is not a rounding detail. It is two different bars of the panel you quoted, and neither page states which measurement it is naming. Which reading suits which class of stock is a judgement against your own stock standards rather than a figure published here, which is why it belongs on the order in millimetres. Note what the pairing does say: six rails across 1.8 m bars a line more closely than five across 1.6 m on either reading.

An assembled line of galvanised livestock panels standing on grass country with hills behind, showing square vertical posts, horizontal rails and pin connections at the joints

Height, stock class and pen layout are worked through in this site’s cattle panel sizing guide. The narrower point here is to write the pitch in millimetres, together with which reading you mean.

Section Shape Is the Open Question

Because the wall is fixed at 1.6 mm across all three blocks, the vertical you buy is a shape decision. Using the standard second moment of area for hollow sections — the stiffness term, where the resisting dimension is the one standing out of the fence line — the four published verticals come out as below. This is a buyer’s arithmetic on the page’s own numbers, not section data from the factory, and it ranks how hard a member is to bend, not when it yields. Strength needs the section modulus worked separately.

Vertical as published Second moment, mm to the fourth Against the 50 x 50 RHS
50 x 50 mm RHS at 1.6 mmabout 121,0001.00
40 x 40 mm RHS at 1.6 mmabout 60,5000.50
42 mm round tube at 1.6 mmabout 41,5000.34
32 mm round tube at 1.6 mmabout 17,7000.15

A square vertical is not marginally better than a round one at the same wall. On the stiffness figures above, the 40 x 40 mm option on the same page halves the number against 50 x 50 mm, and the two published round tubes sit at roughly a third and a seventh of the larger square. That matters because the oval style can be quoted with either vertical: the same headline product, two different frames.

The rails carry a question neither page answers. On the cattle page the oval options are 30 x 60, 40 x 80 and 40 x 120 mm; on the sheep page the same family reads 30 x 60, 40 x 80 and 40 x 115 mm, and the wall ladder there extends to 2.0 mm. Neither page says which face of an oval rail stands proud of the fence line. Approximating the oval as a hollow rectangle of the same outside size at 1.6 mm, 40 x 80 mm gives near 317,500 mm to the fourth with the 80 mm face proud and near 107,700 with the 40 mm face proud. A true oval moves both figures but not the ratio: roughly three times, from one ambiguous row of a specification block.

A beast standing inside an assembled run of galvanised livestock panels on grass, with horizontal rails, vertical posts and welded joints visible along the line

So the lines that decide this purchase sit outside the option list. Name the vertical section and the rail section, and ask which face of the oval sits proud. Ask for wall thickness per component, not per panel, since the two pages offer 1.6 mm and 2.0 mm ladders. Ask how many pins ship per panel, against the six lug openings the second page describes. Ask which coating figure covers rails, weld paint and feet.

Frequently Asked Questions

Why do cattle panels have six rails?

Because that is what the pages pair with a 1.8 m height: 6 bars at 1.8 m, 5 bars at 1.6 m. Six rails into two verticals is also twelve rail-to-post welds, which is the count to confirm on the drawing.

Is an oval rail stronger than a square rail?

Not on these numbers alone. Both families are published at 1.6 mm wall, and an oval rail’s resistance to bending depends on which face sits proud of the fence line: read two ways, a 40 x 80 mm rail is roughly three times apart on that measure.

What holds a cattle panel line together?

Welded caps, lugs, feet and pins on the post, per the cattle page, which states 2 pins per panel. The site’s sheep panel page describes two sets of double lugs plus two single lugs taking 16 mm pins. Ask which applies to your line.

Does galvanising thickness matter on a stock panel?

As a specification line, not a strength line. The oval and square style blocks read “More than 15 microns” while the site records 18-28 microns for this livestock line per the product page, so ask for the figure per component before comparing two quotes.

Conclusion

An oval rail and square post frame is the specification that decides how a panel carries stock, and it is the line most purchase orders leave blank. Height, length and rail count are identical across the three published styles; section shape, wall per component and the lug-and-pin count are not.

Ask for the section drawing, the proud face of the rail and the pitch reading in millimetres before comparing two quotes. The company quotes within 24 hours, so none of this has to wait for a sample panel on a truck.

Facebook
Twitter
LinkedIn
Pinterest
engineer cooperation two asian male female technician maintenance inspect relay robot system with tablet laptop control quality operate process work heavy industry 40 manufacturing factory

Talk To Our Expert

Connect with our specialists to discuss your needs and confidently start your project!

Picture of Frank Zhang

Frank Zhang

Hey, I'm Frank Zhang, the founder of DB Fencing, Family-run business, An expert of metal fence specialist.
In the past 15 years, we have helped 55 countries and 120+ Clients like construction, building, farm to protect their sites.
The purpose of this article is to share with the knowledge related to metal fence keep your home and family safe.

Categories

Recent Posts

Table Of Contents

We are at your disposal for any technical or commercial information

Table Of Contents

Picture of Frank Zhang

Frank Zhang

Hi, I’m Frank Zhang, the founder of DB Fencing, I’ve been running a factory in China that makes metal fences for 12 years now, and the purpose of this article is to share with you the knowledge related to metal fences from a Chinese supplier’s perspective.
Facebook
Twitter
LinkedIn

Ask For A Quick Quote

We will contact you within 1 working day, please pay attention to the email “info@metalfencetech.com”.

Your Email is necessary!!!